The bid bottleneck, and how to break it.

An investor needs a repair number before the seller signs with someone else. A contractor needs jobs without spending every afternoon driving to houses they won't get. They are waiting on each other, and both are losing.

By Jerryll NoordenNovember 20, 202610 min read
Out loud, about 5 minutes. Ask him anything.

The short version

  • Investors usually need a repair number within a day or two of seeing a house. A contractor bid often takes a week.
  • Contractors drive out, walk the house and write a bid, then win a fraction of them. Every lost bid is unpaid time.
  • Both sides are doing the same work twice: the investor walks the house, then the contractor walks it again.
  • One measured, photographed scope can be shared: the investor gets real prices fast, the contractor prices from the desk.
  • Bids built on the same scope can be compared line by line, instead of three totals that describe three different jobs.

The investor's side: the clock.

A motivated seller rarely waits. They are talking to several buyers, and the one who comes back with a firm offer first usually gets the house. To make that offer, the investor needs to know what the repairs will cost.

So they call contractors. On real estate investor forums the same story repeats: the contractor can come Thursday, the bid arrives the following week, and by then the seller has signed. Some contractors don't show at all, because a walkthrough for an investor who doesn't own the house yet is the lowest-priority call of their day. Experienced investors often tell newer ones not to wait for bids before offering at all, and to estimate the repairs themselves, which is exactly where the guessing starts.

Dayshow long a motivated seller waits for an offer
About a weekhow long a contractor bid commonly takes
1 walkthroughwhat a repair number really needs

The contractor's side: unpaid driving.

From the contractor's seat it looks different. An investor calls about a house they might buy. Going out means a drive, an hour or more in the house, and an evening writing the bid. If the investor doesn't get the house, or picks someone cheaper, all of it was free work.

The alternative most contractors use is paying for leads. Shared-lead services commonly charge anywhere from about $15 to over $100 per lead and sell the same homeowner to several contractors at once, so most of those leads are lost too. Either way, a large share of a contractor's week goes into jobs they never get.

Hours spent per job won, at a 1-in-4 win rate

Drive there and back2 h per visit
Walk and measure1.5 h per visit
Write the bid1.5 h per visit
Per job won (×4 visits)20 h

The real problem: the house is walked twice.

Put the two stories side by side and the waste is obvious. The investor already walked the house. They saw the kitchen, the bathroom, the roof, the floors. Then the contractor drives out to see the same rooms again, because the investor's notes, "kitchen needs work, bathroom dated", aren't something anyone can price.

If the investor's walkthrough produced a scope a contractor could price, room by room with quantities and photos, the second visit would be unnecessary for the first number. The investor gets prices in hours. The contractor prices from the desk, only drives out for jobs that are real, and gets work without paying for leads.

One walkthrough, one scope, real prices from several contractors.

What a priceable scope needs.

A contractor will only price a job from the desk if the scope tells them what they would have seen in person. That means:

  1. 1

    Rooms, not a total

    Every item under the room it belongs to, so a contractor can picture the job.

  2. 2

    Quantities

    Square feet of flooring, linear feet of base, number of doors and fixtures. Measured, not guessed.

  3. 3

    Photos on each item

    The photo of the cracked tile sits next to "replace tile, 45 sq ft", so condition isn't a mystery.

  4. 4

    A finish level

    Rental-grade, mid-range or high-end, so everyone prices the same materials.

  5. 5

    Stated assumptions

    What wasn't visible: behind walls, under floors, on the roof. Contractors price those as allowances.

A desk price is a first number, not a contract. Once the investor has the house under contract, the chosen contractor walks it once to confirm. That is one visit for a real job instead of four for imaginary ones.

Bids you can actually compare.

There is a second benefit. When three contractors each walk a house and write their own bid, they describe three different jobs. One includes the permit, one doesn't mention the subfloor, one prices quartz where the others assumed laminate. The totals are not comparable, which is why investors routinely see bids for the same house that differ by half or more.

When all three price the same scope, the comparison is line by line. You can see that one contractor is high on tile and low on paint, and you can ask about it instead of guessing. Here is why bids vary so much and how to read them.

Same scope, three bidsRidgelineBluepointHarbor
Kitchen$14,950$13,820$15,400
Bathroom$7,300$6,980$7,640
Flooring$9,120$8,760$9,900
Paint and trim$6,412$6,050$7,110
Roof and exterior$8,600$8,300$8,950
Total$46,382$43,910$49,000

How EstiMate connects the two.

EstiMate's scope translator is built for exactly this. The investor walks the house with the phone, and the photos become a scope: rooms, items, quantities and a finish level. They send it to the contractors they choose.

A contractor who uses EstiMate sees it priced instantly with their own price list and markup, and can adjust and send it back in minutes. A contractor who doesn't gets a clean bid form with the photos and quantities, and fills in their prices. The investor sees every bid side by side, line by line, often the same day they saw the house.

Same dayrepair numbers from real contractors
0 drivesneeded for the first number
Line by lineevery bid against the same scope
Questions

What people ask first.

Can a contractor really bid without seeing the house?

For a first number, yes, if the scope has rooms, quantities, photos and a finish level. The chosen contractor still walks the house once before work is signed.

Why do investors struggle to get contractor bids?

Because walking a house for someone who doesn't own it yet is unpaid work with a low chance of a job, so it gets scheduled last.

How do contractors benefit from investor scopes?

They price jobs from the desk, skip the drive for jobs they won't get, and avoid paying for shared leads.

How do I compare bids fairly?

Have every contractor price the same scope, line by line, at the same finish level. Then differences show up item by item.

What if something is hidden behind a wall?

State it as an assumption and ask contractors to price it as an allowance. That is normal and keeps bids comparable.

JN
Jerryll NoordenFounder of REILink. Former NASA robotic scientist, flipping houses since 2016. He built EstiMate because every repair number he was handed was a guess.

One walkthrough. Real bids.

Investors get real prices before the offer. Contractors get real jobs without the drive. Both from the same scope.

Free for a week. The week starts on your first property, not the day you sign up.